If your Lexus ES 350’s VSC light comes on, don’t worry. It doesn’t mean there’s something wrong with your car. The VSC system is just meant to help keep you safe while driving.
But if you’d like to reset the VSC light anyway, here’s how to do it:
1. Turn off your car.
2. Open the hood.
3. Locate the VSC fuse box. It’s usually near the battery.
4. Remove the fuse for the VSC system.
5. Wait a few minutes.
6. Replace the fuse and close the hood.
7. Turn on your car. The VSC light should be gone.
Table of Contents
What is the use of VSC lights on Lexus ES 350?
If your “Check VSC System” warning light is illuminated on your Lexus, don’t worry. You can just ignore it and drive sensibly with traction control. If it stays on all the time however then there may be a problem that needs attention.
The VSC system monitors a variety of things with sensors in various parts of the car. If any of these sensors detect a problem, then the system will turn on the traction control to maintain safety.
Why do you need to reset VSC light on Lexus?
Occasionally it might be necessary to reset the VSC warning light on your Lexus. This is easily done by following the simple steps listed above.
The most common reason to reset the light would be if you have had an issue with your car and had it serviced. The mechanics may have turned off the VSC system but forgotten to reset the light afterward.
How long does it take to reset VSC light?
It should only take a few minutes to reset the VSC warning light on your Lexus. Simply remove the fuse, wait for a few minutes and then put it back in. After that you can turn on your car and the light will be gone.
Where is the VSC button located?
TRAC can be disabled by pressing and releasing the VSC Off button located near the gear shift. Check your speedometer for the TRAC OFF indicator light. This is where you’ll find your VSC Off indicator light, as well. The TRAC can be turned back on by pressing the button again.
How do you reset the ESC light?
To turn off the ESC system, hold down the “ESC Off” switch for five seconds and release it. The ESC warning light will illuminate and the odometer will display “ESC Off” as a result of this action.
Can I drive with the VSC light on?
With the VSC light on, it is generally safe to drive. When the light is on, however, you must exercise extra caution due to the absence of your VSC system. To be on the safe side, we don’t recommend driving with the VSC off when it’s snowing or raining hard.
How much does it cost to fix VSC on Lexus?
Lexus vehicles require a fix for the vehicle stability control (VSC), which can be had for between $200 and $300. There must certainly be something else going on if the light was responsible for this. ABS is used by Vsc to communicate with other car components.
What causes check engine light and VSC light on?
The “skidding vehicle” or “TRAC OFF” light may also be illuminated on some vehicles, depending on the model. O2 Sensor or gas cap problems are the most common causes of Check Engine and VSC lights on a Toyota. If you want to save money, tightening or replacing the gas cap is a viable option.
Should VSC be on or off?
Traction Control (also known as TRAC) and Vehicle Stability Control (VSC) may need to be turned off if the vehicle’s front wheels become stuck in fresh snow or mud.
Where is the VSC button on a 2007 Lexus RX 350?
For at least three seconds, press and hold the “Traction Control off” button on the left side of the center console.
Why won’t my traction control light go off?
Detecting when a drive wheel spins faster than the others indicates that the vehicle is either losing traction or slipping. To put it simply, if the traction control light doesn’t go out, the system isn’t working and can’t keep the vehicle from rolling. It’s imperative that the system be examined.
Why does my ESC light stay on?
It’s a sign that your car is out of control if your ESC light stays on. It is possible that your ESC has malfunctioned or been manually deactivated if the ESC light is illuminated for an extended period of time. Any problems with the ESC will cause it to stop working.
What does VSC mean in a Lexus?
Others refer to it as electronic stability control (ESC), but Toyota and Lexus refer to it as VSC (vehicle stability control).
What causes the ESC to malfunction?
When the anti-lock braking system in your car is working properly, electronic stability control performs best. If your ABS is malfunctioning, your ESC may not function properly or at all. Tired brake linings and dirt in the brake fluid are two common causes of 4-wheel ABS malfunctions.
Can you reset check engine light without disconnecting battery?
The check engine light can’t be reset without removing the battery. Using an OBD2 scanner, you can clear the check engine light without having to remove the battery. Most cars’ check engine lights will go out on their own after a certain amount of time of driving after a fix has been made.
How do you reset a car code without a scanner?
Reconnect the battery cables, and then turn the ignition switch ON and OFF three to five times. The horn can be activated by pressing the button on the wheel. It’s best to hold it down for 30 seconds to a full minute to drain the ECU capacitor of all of its stored power. There is a hot wire connected to the horn’s speaker.
How do I reset my Lexus?
As you turn the ignition switch back on, press and hold the Trip Meter Reset button. You must wait until you see the Lexus maintenance light blinking before turning off. It is time to reset the Trip Meter.
Will disconnecting battery reset ABS light?
If the battery is removed from the vehicle for an extended period of time, the ABS light will be reset.
What does it mean when your ABS light and traction control light comes on?
Computer or PCM malfunctions, faulty wheel sensors, or other mechanical failures can cause the ABS and Traction Control lights to flash. When the main brake light goes out along with these warning lights, it may indicate a more serious problem.
How long does it take for ABS light to reset?
Hold the brake pedal down while disconnecting the positive cable from the vehicle’s battery to completely drain the vehicle’s electrical system. Reset the car’s main computer by doing this. To restore power, reconnect the positive cable. For up to a week, even if this doesn’t completely reset the light, it should remain off as a result of using this method.
Will any OBD2 scanner work on my car?
OBD2 scanners are actually compatible with vehicles manufactured after 1996. It’s possible that an OBD1 scanner could be used if the vehicle is older than 1996, but these are more specific to each model of vehicle.
